Features:

  • 【Warm Tips】： To figure out your values for the Sensitivity , Please set the delay time to its minimum value first , this will save your time.
  • 【Motion Activated】 : Sensor function triggered by motion, you can use this small motion sensor switch to control lighting like Led strip lighting.
  • 【Delay Time Adjustable】: The delay time controls how long the light stays on once it gets triggered, during the delay time if motion detected, the delay time will reset and start a new delay time.
  • 【Sensitivity Adjustable】: The sensitivity controls how close you need to be to the sensor in order to activate it.
  • 【Wide Application】: You can use this sensor in different occasions like entryway lighting, cabinet lighting, gun safe lighting, pantry lighting, under the bed rails lighting.
Works like a charm. Adjust time and you will be set

Exactly what I was looking for. A motion sensor for my walk in closet. This works like a charm. The default timer settings are ridiculous. Turns off in a second. Unless you open up and dial up (counter clockwise) the delay time, it will irritate you. Once you adjust, it has fantastic sensitivity and detects motion very well. Highly recommend. Wish they had settings for the timer so you know how much to dial. It has puny little numbers but have no idea what they correlate to. Likely trial & error. Good thing is the back just pops off for quick adjustment.

It works! A great bargain.

I’m using this to control and led light strip in the bathroom of my rv. So far, it works great. The sensitivity is adjustable and can be set to be very sensitive. The time on delay is also adjustable from about 20 seconds to a few minutes. Perfect for my application.

Works great.

I am using this connected to LED lighting for my safe and it is working great. Yes, it is kinda of a pain to take the back off to adjust the dwell time and sensitivity but after I got it dialed in I have been very pleased. If your thinking of using this for safe lighting you can get the whole package, LED lights, power brick and motion sensor for around $26.00. Not too shabby considering safe lighting kits run anywhere from $80 to $200.

Perfect for my safe

I have this in line with my Hitlights LEDs inside my safe. It is confusing how to adjust it, you have to take the back cap off of it and there is no directions that explain that the cap has to come off. I was trying to stick stuff inside the little holes and I'm an electrical engineer that got stymied by this little cheap PIR sensor! It works awesome, very repeatable. Every time I open the door it comes on right away and I spied on it through the crack and made sure it turns off after 2 min. I'm going to install one I my pantry next. Awesome little product and plugs right into the higlights lights in series.

Works as intended

Used in conjunction with a LEDJump LED strip to light up the inside of my gun safe. Had to adjust the timer, otherwise the light turned off in 2 seconds, but the process was painless. Unit is small and easily hidden. Bonus: the power out connector was compatible with one the LED kit included, one less thing to solder!

Works great, just not with dimmer in the circuit

I got this to operate a series of LED light strips I installed under the lead edge of shelves in a quite dark unlit pantry. The LED light strip set I had purchased came with integral dimmer control. I could not get the on/off control for the strip to operate properly until I removed the dimmer from the circuit (all quick connect plugs). Without the dimmer the motion sensor works great. Now when we open the pantry door, the LED lighting comes on instantly just like opening the fridge and shuts itself off within 60 seconds of closing the door. It also turned out that the brightness is just fine even without the dimmer.

Works just fine, read the instructions

Works just fine, you need to open the back of the case to be able to adjust the dwell time. It comes from the factory turned all the way down (clockwise) so it only runs for a few seconds. I adjusted it a half turn (counterclockwise) and it stays on for 5 minutes. DO NOT turn the black plastic dome on the front, this is the motion sensor only. Other reviewers gave low rating because they failed to read the instructions....

... with LED light strip and power supply for really nice safe lighting

Combined with LED light strip and power supply for really nice safe lighting, very happy with the setup. I didn't do extensive testing on the adjustments, but the delay works well enough and the sensitivity when cranked to the max picks my movement up from about 1.5 meters out.

Great Light Sensor

Works great! After minor adjustment, I was able to get dwell time where I wanted it. As stated, read the instructions. The back comes off and there are adjustment "pots" inside, very simple to do.

works great. compatible with HitLights. very sensitive. no need to adjust it.

very sensitive. no need to adjust it. picks up any movement from at least 10 feet away without adjustment. stays on as long as there is movement. turns off about 2 seconds after movements ends, which i guess is adjustable but i find is not necessary for my needs. really nice that it is compatible with HitLights. just plug n play. nice compact design.

Full Reviews