Features:

  • Product Name : Die Spring;Loading Grade : Light Load
  • Color : Yellow;Model : TF 8*20
  • Hole Diameter (OD) : 8mm/0.31";Rod Diameter (Inner Dia) : 4mm/0.16"
  • Free Length : 20mm/0.8";Material : Metal
  • Net Weight : 22g;Package Content : 10 x Die Spring
Must have for my Creality Ender3

Pros: Much better then stock. More consistent prints I dont have to level the bed as much Cons: None. Other thoughts: After installing, level your bed. Then heat up your bed to your normal operating temperature and level it again.

Great purchase! A must have!!!

For an Ender 3, this is a must purchase along with the glass bed. Very easy to install. Just be careful with the back left spring where the wiring harness is so you don’t break the wires to the heat bed. The alignment of my bed has stayed in place so much better after adding these springs.

Amazing bang for the buck upgrade for Ender 3

Even before installing them, you can see and feel the high quality of these springs compared to the stock Ender 3 bed springs. These springs enable much more precise bed leveling increments, and the stability improvement is night-and-day. This is probably the best bang for the buck upgrade for the Ender 3.

Full Stars! Get these and make your Ender 3 Bed Leveling Behave!

You must get these springs in order for your Ender 3 bed leveling to behave. I had serious issues with the leveling staying intact. Each time I dislodged a print from the over-engineered tacky bed liner, the leveling would go off the rails and the nozzle would dig into the bed when the next print commenced. This was because the stock springs were so slack that the vibrations of the machine and removing the prints would easily cause them to lose grip over the leveling knobs causing the bed to rise up closer to the hot end resulting in the nozzle dig! With these new springs in place, the problem instantly disappeared! These are really worth the buy. And besides there are plenty of spares left behind that I can use either on the Ender 3 or it's big brother the CR-10. Full Stars!

Good spare parts to have on hand

Well when I replaced the heating element on my CR-10 S4 one of my springs achieve orbit and was lost. These do make ok replacements. Just note they are 5 mm shorter than originals and a little bit lighter. However so far they work just fine. I would suggest to keeps some on hand just in case.

Excellent springs for Ender 3

I'm just going to be honest: the bed leveling springs that come standard on the Ender 3 are just plain bad. Every print, I needed to relevel my bed. These springs are really stiff and seem to keep the bed consistently level. Plus, these springs are about 1-2mm longer than my stock springs. That means they provide even more tension, which should further help keep the bed level for longer.

Great for Ender 3 Pro

As everyone knows, leveling your bed on an Ender 3 is critical to getting that first layer down. I used to relevel my bed before every print. I have only releveled my bed once in the 2 weeks since I put these springs on. I do spot check here and there, but it’s always right on. The only down side is it took well over a month for these springs to arrive from Asia.

Strong, keeps print bed level better.

Used these to replace the stock bed springs on a Creality Ender 2. Totally worth it; the thing no longer falls off level after every other mildly stuck print. Definitely a recommended upgrade.

If you have a hard time keeping your Ender 3 bed level.... these things are it.

I started out skeptical at first... That atrocious looking photo they use make these springs look way cheaper than they actually are. So I almost returned them before they even arrived. But I went ahead and opened the package when it got here, and was shocked at how firm they were. The blobby looking paint job their photo shows was actually quite smooth, more like a plasticized coating than paint.. Any way, top notch for the price. ONTO THE REVIEW! These springs are quite firm for the hobbiest environment. The length varies from around 20.2mm to 20.7mm with 20.65mm being the most common. At least that's how my particular bag seemed to work out. They actually work perfectly for the Ender 3s bed. I put them on the second they arrived, about 24[10:53am 09-21-2018] hours ago and have yet needed to relevel the bed. I have removed one large and two small prints from it. I have also noticed the vibration lines are significantly less pronounced with these yellow springs installed verses the stock wire springs. Pretty good. That's my rating, pretty dang good. Get em if your Ender 3 springs seem a bit to squishy for your taste, or you notice lots of echos on your prints. These little springs are the bomb, no lie. OK @Uxcell, don't you go changing suppliers and goofing this up. These springs are perfect.

upgrade

when i first ordered my 3d printer, i was watching videos about every upgrade i needed and went and orderes them all before it even arrived. ( an ender3) well, most were bs and crap. this is one of the only actual upgrades that i feel really did anything. they are stiffer than the stock springs, and make the bed feel much firmer. as to weather or not this helps with teh print, idk, but these actually do something, unlike most mods.

Full Reviews