• With special Krallex legs for extremely narrow spaces.
  • With integrated leg clamp to prevent slipping out of position.
  • Used to remove the windscreen wiper quickly and conveniently with higher quality for durable use.
  • Applied to universal vehicles: Audi, BMW, Chevrol/Daewoo, Chryler-Jeep, Citroen, Fiat, Ford, Honda, Hyundai, KIA, Land Rover, Mazda, MG-Rover, Nissan, Peugeot, Porsche, VW, MAN, MB, Scania...etc
  • With the two different hook couples( extra thin straight tips and rounded tips) to fit universal vehicles.

did the job. and the center nut was the same sized socket as the wiper arm nut. removed arms no problem, whereas the cheap one I tried before the t-bar bent and the gripper arms bent also (that wiper arm was really stuck on....)

Last week i just remove my rear wiper arm very easy with the help of Firstinfo wiper arm puller from fit tools. Its been a year i was trying to remove my rear wiper with my friends but unfortunately we cant remove it. Because were affraid we might break the rear glass window. The wiper is installed in the rear glass. The car is Toyota previa 2008 model and toyota Rav4 2004 model. Thank you seller and Amazon for your quality product.

Just Awesome !!!!!! Especially with modern cars that have no room to get a standard wiper puller on the wiper with the plastic shrouding.The thing is built like a tank too.The last wiper tool I'll have to buy.

Look no further. If you ever need to remove wipers this is the tool. Absolutely the best puller for the job.

Best wiper arm remover and out there at the lowest price cost.

Loved the narrow profile. So far, only used it once, but I can see it'll be the first-to-go-to puller for smaller applications. The only negative is, as other have pointed out, the wingnuts. They do tend to get in the way when the arms are close enough to the central bolt. However, they can be swapped out for a dollar or two, so only a minor inconvenience for me.

I struggled (and failed) with multiple pullers and even stripped and ruined one of the cheaper thumb turn $15 wiper puller tools. Less than five minutes after unboxing this puller, I had the rusted rear wiper removed from my 1994 Toyota Land Cruiser. This is absolutely worth the extra $$.

I cracked my windshield trying to use another style puller!! So I ordered these based on the reviews I read and I love them. They work so much easier and they are well made. Good thing my insurance paid for a new windshield:-)

This tool is very well built. Like some have said, the wing nut type fasteners can be a little annoying at times, but it's not a fault as much as it is simply a cost for the convenience of wing nuts. The center driving bolt has a 13mm hex head (if I remember correctly - it was the same as the nut on a 2015 Chevy Sonic rear wiper). The ends of the wing-tip bolts have a nice steel ball bearing termination, which makes them easy to tighten and they don't damage the tool when you tighten them down. The tip of the press is actually a metal oxide coated steel cap, which slides over the end of the driving bolt. The tip of the driving bolt has a ball bearing termination similar to the wing nut fasteners. This design allows the cap to rotate, and makes turning the driving bolt very easy even when there is high tension. When the cap is not pressed against the wiper stud, it is held in place by an o-ring on the driving bolt. The two different tips are great. One allows for access in really tight spaces, and the other provides a nice, wide surface area that pulls on the wiper arm. I used this to remove the rear wiper arm on a 2015 Chevy Sonic. It made the job simple and easy, and I'm glad to have purchased a quality tool. Worth every dollar.

Only complaint are the red twist ears on the top...they kind of get in the way of the tightening bolt. But I would absolutely recommend this product. The hooks are small and fits in almost every make/model of vehicle's wiper arm locking bolt. I don't even use a penetrating spray anymore...just slap this on and crank it down, and pop goes the weasel.