• ULTRA REFLECTIVE POLYCARBONATE LENS - The amber 2.5" round LED side marker uses a specially designed polycarbonate lens to reflect back direct light, allowing your tractor or trailer to be more visible at night and providing a safer driving experience for you and other drivers on the road. The round LED side marker also comes with a "TOP" orientation, designed to allow you to uniformly install multiple units, while maximizing the amount of reflectiveness from each lens.
  • 2 IN 1 FUNCTIONALITY - Driving a tractor, trailer, truck, or any other large vehicle mandates that you drive with side marker lights and reflectors depending on the size of your vehicle. The LED clearance light comes with 13 high powered LEDs, allowing it to serve as both a reflector and clearance light that federal law requires for larger trailers. This LED clearance light is also D.O.T FMVSS-108 compliant.
  • WATERPROOF, SUBMERSION READY - The waterproof IP67 rated LED side markers are fully capable of being submersible. This makes the clearance light ideal for boat trailers that launch and pick up watercraft into the water.
  • EASY INSTALLATION - The OLS red clearance light comes with a rubber grommet so you never have to mess around with screws. Simply use a preexisting hole, or create a new cut out for the grommet, and use the industry standard two prong plug to light up the night.
  • HIGH QUALITY COMPONENTS - Each red 2.5" round LED clearance light uses high quality components made in Taiwan, and is reverse polarity protected, meaning that plugging it in the wrong way will not damage the unit itself. The red clearance light has been certified safe by the D.O.T. and comes with D.O.T. SAE certification printed directly on the unit itself.

I dont normally do reviews but were in the process of updating all our trucks and trailers to led and so far we have changed about 30 lights and absolutely love the price and quality. The leds are bright but not to bright to blind people at night and there a sharp red and amber. The grommets are some of the BEST. Stiff to work with, sometimes a little wd40 is needed but they hold strong and there low profile. New pigtail for every light and pre greased for a good, clean connection. Best part is if you brake them (accidents happen and not a product defect) the actual led bulb is the color and continues to mark your trailer to DOT color code. 5 star lights for sure

Easy to install, it only works in parking lights mode only, i was looking for same size and with signal blinking but so far can't find it. If some one knows where to find them please let me know.

These are nice lights, I updated an older heavy equipment trailer. Nothing like new lights and new paint. These are easy to mount with the correct hole size which is standard size. Some of you are saying they are too big, if that's the case you do not have standard size holes. Irregular holes are common , don't blame the lights.

Very very very hard to take out the old ones and very very very hard to put in the new ones. Used WD 40 and a torch to make the rubber more pliable to work with getting it into the hole. So be prepared with you tackle the job of replacing the old ones.

Bought this to go in the hub opening of my spare tire on my Jeep to utilize as a 3rd brake light, works flawlessly, but time will tell.

Took a chance by purchasing these over the expensive poison spyder ones, and it payed off. They fit nice and snug with my poison spyder rock brawler II rear bumper. Would recommend to fellow jeepers/ anyone if you are in the market for them. Well built strong plastic housing bright leds, connector seemed to be waterproor only time will tell. Will update my review...

Great lights for trucks or trailers, all of them worked and looked good, comes with a template to cut the hole

Theses fit perfectly !!! And light up great . Plugged right in.

Awesome product! Bought these for our dump trucks, they were easy to install and work great. Very bright and look great because they are flush with the bed of the truck. Would definitely buy again.

I had a very hard time making this rubber lip fit the hole. Maybe I didn't have the proper technic.