Features:

  • ★WARRANTY: 24 months warranty for iCreating 5050 4Pin LED strip connector kit, 90 days money back guarantee for any reason, 24 hours online customer service
  • ★PACKAGE INCLUDES: 1x 2 way RGB splitter cable, 2x 6.6ft RGB extension cable, 2x strip to RGB controller jumper, 2x LED strip to strip jumper with wire, 2x L shape connectors, 2x gapless connectors, 20x LED Strip Clips, 20x 4 Pin Male Connector
  • ★APPLICATION: 10mm 4 wire LED light strip connector kit for waterproof and non-waterproof 5050 RGB Color Changing LED strip lights
  • ★OPERATING CONDITION: These LED tape connectors support 0-4A current and 0-24V voltage input, heat resistance level from -20 ~ 100 degree
  • ★NOTE: When connecting waterproof LED strip lights with these LED strip connectors, silicon gel on the surface of soldering area must be peeled off
There is nothing least I like about the 4 pin cord

There is nothing least I like about the 4 pin cord. What I really like is the length and how much of extensions I can make for my RGB color changing strips. Thank you very much and not let the 100 ft. length taken off the market.

Good deal for a two-way LED splitter.

I only needed one of the four to help run some RGB LEDs in my PC case, but was happy to get three extras that I might use for future projects. They are wires coated in plastic with connections for four-pin LED light strips and cables. They carry power and work as expected.

Good accessories.

The link connectors and accessories work great. They can be a little tuff to get to work correctly and flipping the polarity on the connectors is easy to do. A little attention to detail and they should work great. Once you get the hang of it they are great additions to your light kits.

Great multi use kit, everything needs for small jobs

Exactly what I needed for setting up a couple of short led strips over my stairs. The clips are strong and ridges, the snap connections worked very well. The 4pin keys do not hold super tight but some electrical tape hold the pieces together well.

Great for repairs

I am going to use these as a lead to a set of LED lights where the end has come off. Easy to use, just put the wires in place and close. Note that you need to look at the end to figure out how to open.

Good stuff for projects

Exactly what I wanted. A big pile of 4-conductor RGB stranded wire. Good stuff for projects.

YOU NEED THIS TO INSTALL ANY JOB

I have bought several kits and had to splice the lights and did not have the proper connectors to finish the job This kit allows you to connect another set of lights in a total different location using the same power source It also allows all your connections to be done without soldering A must have kit

These pigtails work great!!!

These pigtail connectors work great for LED strip cabinet Installations. I have installed vertical runs of LED strip on each side of each cabinet, on the rear side of the cabinet trim. I use these pigtails to connect the vertical LED strip and then feed the pigtail end up thru a drilled hole to the top of the cabinet. I connect each pigtail to a terminal strip, I found on Amazon, that I have mounted on the top of the cabinet (out of sight) and then connect the terminal strips together using four wire cable that I also found on Amazon. I then use a different pigtail connector that will connect to the final terminal strip and to the LED Strip Controller. I have used this technique in four different cabinet systems and have used about 15 of the pigtail connectors and all have worked flawlessly. A couple of hints when using these connectors: 1. Make sure the edge of you LED strip is cut straight with complete copper lands. 2. Open the connector cover completely so that the connector terminals are visible. 3. When inserting the LED strip into the connector, make sure the strip is inserted into the slot at the bottom of the connector. 4. As you push the strip into the connector, make sure that the copper lands of the strip are directly under the four contacts of the connector. 5. With LED strip in place in the connector, close the connector cover and press down until a "click" is heard. Note: You may need to use a set of pliers to properly seat the connector cover. When connecting the wire end of the LED Strip connector, Make sure colors are matched up and then connected properly to the LED Controller: Black to 12V+, Red to R, Green to G and Blue to B.

convenient

Most convenient item for installing small wire items. I use them when installing LED lights in my cars both interior and exterior. The wires are held in with a small screw clamp, no soldering needed. then you have a barrel plug. This is the second ;time I have ordered these.

Highly recommend!!

Exactly what I needed to make my LED strips work. Great accessory kit! Just make sure to match BRGB to BRGB. If reversed lights wont work. Connectors are labeled. Very easy to use, and work well!

Full Reviews