Features:

  • Compatibility: Jeep Grand Cherokee 2011-2019, Dodge Durango 2011-2019
  • Easy Installation, NO DRILL is required
  • Interchange Part Number: 82212055
  • Materials: Brushed Stainless Steel with Black Antislip Rubber
  • Package included: 2 pcs/set (gas and brake pedal covers)
Very Nice Pedal Covers.

WOW! One nice set of covers that look really sharp.!!! I put them on in 10 minutes. What I did was applied silicone to the edge of brake and gas pedal. Not a lot......sprayed on finger and applied inside both covers and used a stub length slotted screw driver. Work the screw driver blade all around making sure no areas of the rubber tab are sticking out. Make sure they are locked on, on all 4 sides. I cleaned them up with a small amount of Armor All and a towel. Love the look.

Sporty

2017 Dodge Durango R/T fits perfectly Brake peddle was hard to put on. I used a heat gun on low to soften up the rubber (not hot). Use soapy water (I used simple green) on the rubber edges. I slid the cover from the left to the right using the little circular cut out on the top right corner. All I needed to do was pull the right side flap over the brake peddle. The other peddle slipped on with just a little simple green. Hope it last! Because it looks great.

I like 'em

I received the pedal covers as scheduled, and had them installed 10 minutes later. Helpful tips: 1. The accelerator cover is easier to put on from the top to bottom. Use your fingers to pull the rubber edges out over the accelerator on the sides, then the same on the bottom. 2. The brake cover replaces the stock one. Start from the bottom left and work up to the top right. The top right has a notch that i used to slide a screwdriver over the top to the left corner, allowing you to pull the rubber out over the edges. 3. The right side of the brake cover is where you will spend most time. Just be patient and use the notch in the top right corner to slide a small screwdriver down to pull the rubber out over the edges. It will take some time to get it done, so be patient. The look great.

Great Look and Feel.

I love the upgraded look and feel of this product. They are a significantly better product than the OEM rubber pedals on my 2017 Grand Cherokee Altitude. Recommendation: after watching several unboxing and installation videos, all I can say is warm the brake pedal up by soaking it in HOT water. The gas pedal goes OVER the existing pedal quite easily but the brake is a replacement. You have to remove the existing brake pedal cover and putting the new one on can be a pain if the rubber liner isn't flexible. Soaking it in hot water prior to installation was the key. Total install time was 5 mins.

Fit perfect in my 2017 Dodge Durango

Fit perfect in my 2017 Dodge Durango. Even breake panel did not give my a any head ache, it slipped in easy with little bit soap water and the price was right.

Takes a little work to put it on, But worth the result.

Fit really nice on my 2018 grand cherokee. Dont hesitate to buy it. Great price for the pedal covers. Applying the product. Remove first the current pedals covers. ( i just removed the break pedal) the gas pedal is not removal. At least for my car. Spray a little bit of soap, once one side is on the pedal, apply a little presure and swivle around it until you feel the product stay on tack.

Easy install and looks great!

I read some of the other reviews and followed their advice. A little silicon spray on the inside lip of each pedal cover to start. The gas pedal slides on easily, about 30 seconds of work there. I started from the top on that one. 10 seconds to pull off the existing brake pedal pad and then a couple minutes to slip on the new one. Silicon spray and a small standard screwdriver, to pull the lip over the pedal’s edge and it was over. They look great and with an install time of less than 5 minutes, I’d say this was a rousing success. Now I just need to find a matching parking brake cover...

Easy install and added aesthetics

Did not need soap as others had (2015 Jeep GC Limited). Simply removed existing rubber covers and slid these on. Required a little finagling, but otherwise went on easily. Nice look if you have chrome elsewhere on your vehicle. The rubber grips are also a nice feature if you're barefoot.

Cool

Very nice look now when I enter my Grand Cherokee, the gas pedal install was very easy, the Brake pedal was a little tricky, I just turned on the heat thru the upper vents held the new pedal next to the vent to soften the rubber a bit and it went on much easier. Very cool pedals look nice and they are not coming off, nice and tight.

Perfect fit

Perfect fit for my 2018 Dodge Durango. Just put them in a small bucket of warm water to soften up the rubber a little. Then install the gas pedal cover over the existing factory plastic gas pedal. Remove the factory rubber brake pedal cover and install this brake pedal over the exposed metal brake pedal. It can be a little tight fit during the install but that’s how you want it so it stays on while in use. Once on, perfect fit.

Full Reviews