Features:

  • Works on 90° corners and “T” joints
  • 1" maximum capacity
  • Cast aluminum “V” and Wedge Clamp pads
  • Automaxx Auto-Adjust technology
  • Cutout allows driving a pocket-hole screw without removing Clamp
They work

I used them to build a box with cubbies for shoes. It held the shelves nice and square for me while the glue dried. I also bought a pair of cheaper clamps that do the same job. These were slightly easier to use, but cost a lot more. I'd buy them again though. I read reviews about the adjustment screw being too small and hard to turn. It's only hard to turn if there is pressure. I'm able to turn the screw with my thumb. If I can't turn it, I loosen the clamps then try again.

pissed me of at first

got so mad at first almost thru them away! thankfully I finally calmed down and called tech support they talked me thru a simple fix and I am now a big fan

Love it!

Love the entire Kreg collection!

Great product

Works as stated, night quality as with all kregg products. Will buy again soon

Easy to use for butt joints

The clamp doesn't have all the grip of any face clamp or else, but it works fine for the main use, butt joints at right angles. The main purpose is to hold the pieces together in order to use screws or pocket hole joints, that works as designed. Do not expect gorilla pressure on the clamp, it is not intended for that, only to keep the pieces at 90 degrees and use pocket holes, screws and nails. I wish to have one of this on my first cabinet I used a corner clamp since the main intention is to hold everything in order to put the screws. The adjustment screw is easy to use.

Best corner clamp of all

Easy to use, accurate and QUICK. With a little practice you can clamp a corner in a few seconds. I have a pile of different brand corner clamps including the very heavy, but tricky and time consuming to set right, Bessey. The self adjusting feature is ideal for a corner clamp when I need to hold different thicknesses of wood at 90 degrees. Usually I only need to hold a corner for a few seconds while I attach both sides with some glue and brads. The Kreg clamp allows you to go from corner to corner quickly so you don’t need to buy a bunch of clamps.

Useful and practical tool.

It really works well. Holds corners tight. I will buy another

Great for pocket holes

True 90. Great for kreg holes. Better clamps if you are not using with pocket screws.

You can never have too many clamos

Bought for Fathers Day. Can never have too many clamps.

Thought they where broken, but

I purchased 2 of these clamps. Neither one will hold 3/4 inch plywood when assembling a cabinet. I have a right angle clamp by Kreg that uses the same auto adjust that works like a charm. I may have been lucky enough to get 2 defective clamps. So I contacted Kreg about this. The same day I received a reply describing how to reset the clamps and it this doesn't work to let them know. So I followed the instructions and the clamps begin to work like they should. I have to commend Kreg on their quick response. Here is how to reset the auto adjust clamps. " So you will open the jaws and back out that adjustment screw to the point where it is really loose but not falling out. You should see around 3/8" of threads between the bottom of the head of the screw to where it screws into the mechanism. Then you will close the jaws then open them back up. After that, you can bring that adjustment screw back to the positive around halfway down and try to clamp it down. That adjustment is not an exact adjustment, you may have to tighten it more or loosen it more to get the correct pressure you want to apply. When you are using the clamp, you will want to make sure you are opening the clamp fully when you are moving the clamp. This will allow the Automaxx system to reset to zero each time. You should only need to adjust the adjustment screw if you need to add or take out pressure from the clamp as the clamp will adjust to different thicknesses on its own. "

Full Reviews